If you’ve ever worked with embedded systems, industrial controllers, or retro tech repairs, you’ve probably run into a moment where a stubborn NAND flash chip has died or needed a upgrade. As a NAND flash supplier, I’ve seen dozens of engineers and hobbyists rush into soldering these chips without the right prep, ending up with cold joints, damaged pads, or ruined boards. Soldering a NAND flash isn’t the same as soldering a through-hole resistor—it’s tiny, delicate, and one misstep can cost you a hundred dollars’ worth of chip or a working motherboard. Today, I’m breaking down exactly how to do it safely, with steps I’ve tested on hundreds of our own NAND flash units, so you can avoid the mistakes even seasoned makers make. Nand Flash Chip

First, let’s cover the basics that most people skip: understanding what you’re working with. NAND flash chips come in two main surface mount packages: BGA (Ball Grid Array) and TSOP (Thin Small Outline Package). TSOP chips are the older, flatter ones with leads along the sides, perfect for soldering with a regular iron. BGA chips are smaller, with balls soldered to the bottom, and they’re way more common in modern devices—from smartphones to industrial routers. I’d wager 70% of the NAND flash requests I get are for BGA, so we’ll focus on that as the primary target, with a quick note on TSOP at the end for anyone still working with older gear.
Before you even pick up a soldering iron, prep work is non-negotiable. Skipping this step is how you damage a chip before you even heat it. First, gather your tools: a fine-tip soldering iron (25W for TSOP, 30W for BGA is ideal), lead-based solder (it flows better than lead-free for small joints, especially on delicate chips), flux core solder wire (0.5mm or thinner for BGA), liquid or gel flux (critical for BGA, where the balls are hidden), a hot air rework station for BGA, a pair of fine-tip tweezers, isopropyl alcohol (99% purity, no water content) and a lint-free cloth, and a magnifying glass or a microscope if you have one (this is not optional for BGA—pads and balls are too small to see with the naked eye). Also, make sure you’re working on an anti-static mat. NAND flash chips are ESD-sensitive; a tiny static discharge you can’t feel is enough to fry the internal memory controller, so even if you think you’re not static-prone, ground yourself to the mat before touching the chip.
Next, the step-by-step process. Let’s split it into two parts: soldering a new BGA NAND flash, and replacing a old one. We’ll start with a new chip, since that’s the most common ask from our customers.
For BGA NAND flash soldering:
- Prep the PCB first. Old PCBs often have oxidized pads from age or previous soldering. Take your isopropyl alcohol and a lint-free cloth, clean the area where the NAND will sit until it’s completely free of residue. Then apply a thin layer of liquid flux to the pads. Flux is key here—it prevents oxidation during soldering and helps the solder balls form solid joints. Skip the flux and your joints will be weak, or they won’t form at all.
- Prep the new NAND flash. If you’re using a brand new chip from our warehouse, it comes with pre-soldered solder balls, but sometimes those balls are loose or uneven. To fix that, place the chip on a heat-safe surface, apply a small amount of gel flux to the ball side, then gently heat the balls with your hot air rework set to 300°C (572°F) for 5-10 seconds. Don’t hold the heat too long—NAND flash specs say maximum temperature exposure for the chip body is 350°C for 10 seconds, so err on the side of lower heat. The balls should melt into smooth, uniform spheres. If they’re lumpy, you can gently tap the chip with tweezers while the solder is still molten to spread them evenly.
- Align the chip perfectly. This is make or break. BGA chips have a notch or a small dot on one corner that matches a similar mark on the PCB’s pad layout. If you misalign it, you’ll short out pins or ruin the chip. Use your fine-tip tweezers to pick up the chip, then lower it slowly onto the PCB. Don’t press down hard—let the solder balls settle naturally into the pads. Double-check the alignment with your magnifier; even a 0.5mm shift is enough to cause connectivity issues.
- Solder the chip. For BGA, hot air rework is the standard method. Set your hot air rework station to 320°C (608°F) and an air flow of 10-15 L/min (low flow so you don’t blow the chip off the board). Hold the nozzle 1-2 cm above the chip, and move it in a circular motion to distribute heat evenly. Watch the solder balls through your magnifier—they’ll turn shiny and round when they’re fully melted. Stop heating as soon as that happens; overheating will damage the NAND’s internal circuits.
- Clean and test. Once the board cools for 2-3 minutes, wipe the area with isopropyl alcohol and a lint-free cloth to remove excess flux. Then test the chip: if it’s a replacement in a router or embedded system, power the device on and check if the device recognizes the NAND flash. If it’s a prototype, use a NAND reader to verify the chip’s storage capacity and read/write speeds.
For TSOP NAND flash, which is simpler: the process is almost the same, but you can use a standard soldering iron instead of hot air. Clean the PCB pads, apply flux, then heat the iron, touch the tip to both the pad and the chip’s lead, and feed a tiny amount of solder. Work one pin at a time, making sure each joint is smooth and not bridging to adjacent pins. Once all pins are soldered, clean the area with isopropyl alcohol to remove excess solder.
Now, common mistakes I see customers make all the time. First, using lead-free solder. Lead-free solder requires higher temperatures, which puts way more stress on the NAND chip’s delicate packaging. Even if your local regulations encourage lead-free, for NAND flash soldering, leaded solder is the better choice for a reliable joint. Second, not using enough flux. I’ve had customers send back chips they soldered complaining “it doesn’t work” and when I test it, the joints are oxidized because they skipped flux. Third, overheating the chip. A lot of hobbyists crank the hot air to 350°C and hold it for 30 seconds, which melts the chip’s packaging and damages the memory cells. Always check your NAND’s datasheet (we include a free datasheet with every chip we ship, by the way) for exact temperature limits. Fourth, misaligning BGA chips. It’s easy to shift the chip a little when placing it, so take the extra 10 seconds to double-check alignment under magnification. Even a 0.3mm offset can cause half the pins to not connect, leading to the device not booting or the NAND being unrecognized.
If you’re replacing a faulty NAND flash chip, the first step is desoldering the old one, which has its own set of rules. Desoldering a BGA chip: apply gel flux to the old chip, set your hot air rework to 340°C (644°F) and slightly higher airflow, heat the chip evenly until the old solder balls melt, then use tweezers to gently lift the chip off the board. Don’t yank it—if it’s stuck, heat it a little longer. Once the chip is off, you’ll have leftover solder balls on the PCB pads. Clean those by applying flux, then using a solder wick to pull up the excess solder. Make sure the pads are flat and clean before soldering on the new chip.
Another tip: when buying replacement NAND flash chips, make sure you get the exact model number, or a compatible one with the same pinout, voltage, and capacity. A lot of people try to use a higher capacity chip than their board supports, which can cause compatibility issues. We’ve worked with hundreds of engineers to match the right NAND to their boards, so if you’re not sure, just reach out—we can help you pick the right chip for your project.
Now, safety notes: never solder NAND flash chips near flammable materials, always work in a well-ventilated area, and make sure your tools are properly grounded. If you’re new to soldering, practice on old PCBs or cheap resistors first before moving to a delicate NAND chip—this will help you get comfortable with heat and alignment without risking a costly chip.

At the end of the day, soldering a NAND flash is all about patience and prep work. Rushing through the steps is how you make mistakes. As a NAND flash supplier, I’ve seen firsthand that a well-soldered chip will last for years, while a sloppy one will fail within months. If you’re working on a project, upgrading a device, or repairing a faulty NAND, and you need a reliable chip or have questions about the soldering process, feel free to reach out to our team for assistance. Our experts can help you choose the right NAND flash, answer your soldering questions, and make sure your project goes smoothly.
Dual Interface OTG USB Flash Drives References
- NAND Flash Reliability Handbook, JEDEC Solid State Technology Association
- Surface Mount Soldering Guidelines for Semiconductor Devices, IPC Association Connecting Electronics Industries
- ESD Protection Guidelines for Semiconductor Components, Electrostatic Discharge Association
Shenzhen Tanshuo Technology Co., Ltd.
As one of the most professional nand flash chip manufacturers in China, we’re featured by high quality customized products. We warmly welcome you to buy cheap nand flash chip in stock here from our factory. If you have any enquiry about pricelist and free sample, please feel free to email us.
Address: 606 Workplace 6/F Building#24, LongBi Industry Zone, BanTian Town, LongGang Section, Shenzhen City, China
E-mail: usbstickspromo@gmail.com
WebSite: https://www.fondatop-usb.com/